![]() The response time is faster than a slab or over-pour installation but still relatively slow. Thin bubble wrap insulation with a reflective coating is installed under the tubing to encourage the heat up towards the floor. The tubing is placed into the track and once heated, the aluminum transfers the warmth evenly over the floor. ⇐Pictured here is the most common method of installing radiant heat on levels above the basement is known as “staple-up.” In a staple-up installation aluminum heat transfer plates, with a track to accept the tubing, are fastened to the under side of the floor in the joist cavity. ![]() Once cured, it will perform in a similar way to the radiant slab described above. ![]() The tubing is fastened to the subfloor and a light weight gypcrete is pumped onto the floor covering the tubing. The “lightweight over-pour” is a way to achieve the same mass on upper level living floors. The recommended way to control a radiant slab is to “set it and forget it.” It is also the slowest to respond to adjustments of the thermostat due to the mass of concrete that needs to either heat up or cool down. This method referred to as “radiant slab” is the least expensive means of installation. Tubing can be tied to box mesh and poured directly into a concrete slab or basement floor to create a thermal mass. HOW IT IS INSTALLED: There are many different ways to install radiant heat. Example of a dry panel radiant installation. But not all radiant heating systems are created equal. What could be better on a cold, windy winter day than a cozy warm floor to walk on? Radiant heated floors are considered to be one of the most comfortable, steady and efficient ways to heat your home. Detroit Radiant Products manufactures and assembles in the USA.RADIANT HEAT – Not all Radiant Heating Systems are Created Equal. And while you’re installing a heater overhead, ask us about Lumerica lights. No matter your commercial or industrial heating needs, our experts will work with you to find the right solution. Great Lakes Radiant & Industrials offers product lines including Re-Verber-Ray infrared radiant tube heaters and Re-Verber-Air hot air heaters manufactured by Detroit Radiant Products. This is due to the less direct heat transfer experienced when in-floor heat is installed. In-floor radiant heat does not offer freeze protection on the above ground equipment, does not perform well in spaces with high air changes, and will not warm people, tools, or other items in the space directly. This provides freeze protection for items in the space while requiring lower ambient air temperatures. Mounted from the ceiling, the heater radiates infrared heat down to all objects below–people, equipment, tools, boxes, the floor, etc. Infrared radiant tube heaters can heat all surfaces in direct line of sight from the heater. In most cases, infrared radiant tube heaters produce near-immediate results and they are also easily turned back for overnight or non-work time settings. Even in good working condition, the slower response time of radiant floor heat means longer wait times for the space to be warm. Sometimes it’s possible to diagnose the problem from the ground using the indicator lights available on certain Re-Verber-Ray tube heater models. In order to repair an infrared tube heater, all you need is a ladder or lift to access the burner box. In-floor radiant heat is often difficult and expensive to repair because it isn’t easily accessible. Once installation is completed, it’s even more clear that radiant tube heaters are the better choice. Conversely, radiant tube heaters hang overhead making air intake and exhaust a snap–take air from and vent into the space or easily go through a side wall or roof for access to outside air. In-floor radiant heat requires a separate room for the boiler or water heater to ensure access to a clean environment. Not only is it mostly done with new construction, but it can be very costly to retrofit into an existing space and is usually expensive and labor intensive to install. Radiant tube heaters are economical to purchase and install, can be installed in most applications and are versatile enough to adapt to various layouts–they work in virtually any space. But what if you already have a workshop that needs heat, or find that in-floor radiant heat is too complicated? Let’s explore some differences between in-floor radiant heat and infrared radiant tube heaters. Most often, radiant floor heat is considered for new construction because it must be installed before the concrete floor is laid. As the concrete warms, it radiates heat upward to warm the rest of the space. In-floor radiant heat consists of a network of tubes, laid prior to pouring concrete, through which hot water flows to heat the concrete. When considering ways to heat a large space many people inevitably come across the option of radiant floor heat.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |